Editiorials
Events
Turning
19.09.2017|EMO 2017 - World premiere: MULTISPRINT 25 / MULTISPRINT 36

Revolution in automatic turning – multi-spindle automatic lathes for SWISSTYPE machining with a turning length of up to 180 mm

DMG MORI combines SWISSTYPE technology with the productivity of a multi-spindle automatic lathe. In combination with a Y-axis in each spindle position as standard, highly complex workpieces can thus be completely machined with standard tools.

  • Use of driven tools in all spindle positions
  • Y-axis in all spindle positions as standard
  • SWISSTYPEkit for short and long turning of lengths up to 180 mm
  • Chuck and bar machining
  • Bar diameter up to 36 mm, chuck components up to 50 mm in diameter
  • Spindle speed up to 7500 rpm
  • Double-rear and off-centre machining
  • State-of-the-art control technology: FANUC Series 30i
  • Compact footprint (21.9 m²) incl. bar loader and filtering unit

MULTISPRINT by DMG MORI
The MULTISPRINT 25 and MULTISPRINT 36 are setting a new standard in series production with six spindles.

With the experience from more then 5,000 installed multi-spindle automatic lathes, GILDEMEISTER Italiana is an unchallenged centre of excellence in the field of automatic turning. Now that the site in Brembate di Sopra has been completely modernised and therefore the product area has been reinforced over the long term, DMG MORI is presenting a completely new multi-spindle concept in the form of the MULTISPRINT model series at EMO 2017. Because of their compatibility with the SPRINT model series, the MULTISPRINT 25 and the MULTISPRINT 36 are an extremely safe investment. Their production capacity corresponds to that of three to four SPRINT machines. The world premières have redefined automatic turning, and will continue the success story of GILDEMEISTER Italiana. Managing director Mario Stroppa has the following to say: “The new MULTISPRINT is the perfect machine for drastically increasing productivity in the manufacture of long turned parts. We have breathed new life into the technological spirit of GILDEMEISTER Italiana with this development and demonstrated our skills.”

“For the first time we are combining the SWISSTYPEkit that is known from the SPRINT model series with a multi-spindle automatic lathe”, says Mario Stroppa. The MULTISPRINT 25 and MULTISPRINT 36 would therefore set a new standard in series production with six spindles. Each spindle position already has a Y-axis in the standard. On the basis of countless technology studies and a wide range of customer requirements, the developers have fulfilled the requirements for reducing throughput times and set-up times, lowering the cost of process development and integration and also dealing with the increasing degree of complexity. Nozzles in fluid technology, implants in dental technology and shafts in car construction are just three examples of complex components which can be manufactured in a highly productive way on the versatile machines. The result is a manufacturing solution for scalable requirements from series production start-up to series production itself.

With the new multi-spindle automatic lathes, DMG MORI has developed a highly flexible machine concept which productively manufactures complex turned and milled parts in both chuck and bar machining. The bar capacity is a diameter of 25 mm with the MULTISPRINT 25 and 36 mm in the MULTISPRINT 36. The cross-slides on the six spindles (optionally up to eight) all have a Y-axis with travel distance of 100 mm and an X-axis with travel distance of 50 mm. The Z-axis travel distances are 100 m in the standard version, and 180 m in combination with the SWISSTYPEkit. With this, the MULTISPRINT machines can be converted from a short automatic lathe to a long automatic lathe in less than two hours. The maximum turning speed is 7500 rpm.

The MULTISPRINT 25 and MULTISPRINT 36 can manufacture even extremely complex workpieces effortlessly because of their up to 28 tools. Up to 24 driven tools can be used. The speeds go up to 13,800 rpm or maximum torque of 14.2 Nm.

For rear machining the MULTISPRINT machines can be optionally equipped with a pick-up spindle or one or two counter-spindles. The cycle times can be reduced by up to 35 percent in this way. The pick-up spindle move 230 mm along the Z-axis.  The one or two counter-spindles move 280 mm along the X-axis, 320 mm along the Y-axis and 370 mm along the Z-axis. A double tool station with three driven and two fixed tools completes the scope of the equipment. Demanding off-centre machining is also possible. The indexing of the counter-spindles is a high-precision 0.002° in both configurations. As far as control is concerned, the two multi-spindle lathes are equipped with a DANUC series 30i.

On the automation front the MULTISPRINT machines can be equipped with a bar loader. DMG MORI has developed its own bar loader especially for the new MULTISPRINT machines. Up to two robots can be used directly in the work area for machining chuck components. These take care of simultaneous loading and unloading and the turning of chuck components with diameters of up to 50 x 80 mm.

Regarding the reliability of the machines, Stroppa adds: “We offer our customers maximum practical maturity of the machines right from the start. We therefore test the machines for 12 months with five selected customers under practical conditions. Regular deliveries will be starting in early 2018.”

Contact us for all issues related to the DMG MORI technical press.

DMG MORI uses cookies to ensure you the best experience on our website. When you browse the website you agree to our use of cookies. More information on data protection and  revocation.

Terms and Conditions    Imprint    Exlusion of liability